Oil Sludge and Slop Oil Recovery with Three-Phase Decanters
Three-phase decanters that turn slop oil, tank bottoms and lagoon sludge back into oil, water and a compact solids cake.
Refineries, terminals, oil fields and industrial plants all collect oily residues: slop oil skimmed from separators, tank bottoms from cleaning, and sludge that has settled in lagoons for years. Disposed of as they are, these wastes are expensive to haul, burn or landfill. Separated with a heated, three-phase decanter centrifuge, most of the oil can go back to the process, the water goes to treatment, and only a small solids cake is left for disposal.
The challenge: stable emulsions
Oily sludge is rarely a simple mix of oil, water and sand. Fine solids, surfactants, resins and waxes hold the oil and water together in an emulsion that may not separate in a settling tank even after days. The composition also changes from load to load, so a fixed treatment recipe does not work for long.
Volume
Water and fine solids make up most of the waste, and every cubic metre of it costs money to haul and dispose of.
Lost oil
The oil locked in the emulsion has value as recovered crude or fuel, but only if it can be cleaned up.
Changing feed
Tank bottoms, slops and lagoon sludge vary in oil, water and solids content, viscosity and temperature.
Typical process flow
Generic flowsheet for illustration. Every Archer system is designed to its own basis; ask us for one drawn for your plant.
How the process works
Condition
The sludge is collected in a heated, mixed tank. A demulsifier is dosed to weaken the emulsion, and coarse debris is screened out.
Heat
A feed pump on a VFD sends the sludge through a heat exchanger to typically 70–90 °C, which lowers the oil viscosity.
Separate
The three-phase decanter splits the feed into oil, water and solids in one pass. Polymer can be added to the feed to capture fine solids.
Polish
Where a better oil quality is needed, a disk stack separator removes the last water and fine solids from the oil.
The water phase goes on to the plant’s effluent treatment, often a lamella separator or DAF system. The solids leave the decanter as a cake that is far smaller than the original volume of sludge.
What Archer supplies
HAUS three-phase decanters
Decanters from our partner HAUS Centrifuge Technologies, with variable bowl and scroll speeds and an adjustable liquid discharge to set the oil–water interface.
Disk stack oil polishing
Self-cleaning disk stack centrifuges to bring the recovered oil to the quality the buyer or refinery needs.
Chemical and polymer systems
Dosing skids for demulsifier and other chemicals, and polymer systems for fine-solids capture.
Controls and packaging
Control panels with IIoT remote monitoring, on a skid or in a container that can move between sites.
Classified (hazardous) areas
Archer designs and supplies centrifuge packages and control panels for classified (hazardous) areas, for example Class I, Division 2, to suit each site’s area classification.
Typical design basis
The figures below are typical. Every oily sludge is different, so we confirm the separation by testing before we size a system.
| Feed | Slop oil, tank bottoms or lagoon sludge; oil, water and solids content varies widely |
|---|---|
| Feed temperature | Typically 70–90 °C after heating |
| Conditioning | Demulsifier and polymer as selected by testing |
| Oil recovery | Most of the free oil, typically 80–90 % |
| Volume to disposal | Typically reduced by 70–90 % |
| Oil polishing | Optional disk stack separator |
| Installation | Skid or container; hazardous-area design (for example Class I, Division 2) where the site classification requires it |
Typical values for illustration only. Results depend on the sludge and are confirmed by testing.
Why Archer Separation
From sample to running plant
- Engineering, not just equipment. Our engineers draw the process, size the machines and write the control philosophy, then commission the system and train your operators.
- Our own design tools. EPLAN for electrical design, SolidWorks for 3D models, OpenFOAM for CFD and code_aster for FEA, so panels, skids and containers are checked before they are built.
- Testing before you buy. A heated lab-centrifuge test on your sludge shows how much oil, emulsion, water and solids it holds, and which chemicals break it; a site trial confirms the result at full scale.
- Rental and demonstration unit. Our containerized decanter can run on your site, on your material, before you commit to a permanent plant.
- Local support. Service and spare parts from our team in Canada and the US, with remote monitoring to tune and troubleshoot from our office.
Related pages
- Decanter Centrifuges: two- and three-phase decanters and how they work
- Disk Stack Centrifuges: separators for polishing recovered oil
- FRP Lamella Separators: free oil and grit removal from oily water
- DAF Systems: clarification of the separated water
- Chemical Systems: demulsifier and chemical dosing skids
- Containerized Centrifuge Systems: mobile units for tank cleaning and lagoon work
